تفاصيل المنتج:
|
شرط: | الأصل جديد | ضمان: | 12 شهر |
---|---|---|---|
شرط الشحن: | DHL / TNT / UPS / FEDEX إلخ. | اسم: | هانيويل التبديل الحد |
خاصية: | المواد الصلبة | نوع: | مكافحة التآكل |
تسليط الضوء: | الدقة الحد التبديل,التبديل الحد المغلقة |
Ironman Technology Co.، LTD
العلامة التجارية المميزة:
● HONEYWELL ● AB ● اومرون ● سيمنس ● شنايدر
● ROSEMOUNT ● ABB ● NOTIFIER ● MTL ● GE ● وغيرها الكثير!
جديد C6097A2310 مفتاح ضغط هانيويل الجديد في المخزون DHL الشحن
مهلة: 3-5 أيام
جديد مع ضمان سنة واحدة
تطبيق
The gas pressure switch C6097A is used to detect the pressure of city gas, natural gas, LP gas or air etc. When the gas pressure changes, the diaphragm of the pressure receiving part detects it and operates the (SPOT) switch to ON/OFF control of the external electrical circuit. يستخدم مفتاح ضغط الغاز C6097A للكشف عن ضغط غاز المدينة أو الغاز الطبيعي أو الغاز LP أو الهواء وما إلى ذلك. عندما يتغير ضغط الغاز ، يكتشفه غشاء جزء استقبال الضغط ويقوم بتشغيل مفتاح (SPOT) على ON / OFF السيطرة على الدائرة الكهربائية الخارجية. These switches are widely used to detect the upper limit or lower limit pressure of gas or air to be supplied to a gas burner, or to detect the clogging of the interlock filter of a burner blower تستخدم هذه المفاتيح على نطاق واسع للكشف عن الحد الأعلى أو الحد الأدنى لضغط الغاز أو الهواء المراد تزويده بموقد غاز ، أو للكشف عن انسداد مرشح التعشيق لمنفاخ الموقد
التركيب
1. Read these instructions carefully. 1. اقرأ هذه التعليمات بعناية. Failure to follow the instructions could damage the product or cause a hazardous condition. قد يؤدي عدم اتباع التعليمات إلى تلف المنتج أو التسبب في حالة خطرة. 2. Check the ratings given in the instructions and on the product to make sure the product is suitable for your application. 2. تحقق من التصنيفات الواردة في التعليمات وعلى المنتج للتأكد من أن المنتج مناسب لتطبيقك.
Accurate pressure set point adjustment (stand alone only) (tolerance <3% over total scale) 1. Remove the screw from the test nipple inlet. ضبط نقطة ضبط الضغط الدقيق (قائم بذاته فقط) (التسامح <3٪ عن المقياس الكلي) 1. قم بفك المسمار من مدخل حلمة الاختبار. 2. Connect the tube of the pressure measurement device to the nipple (Fig. 1. F). 2. قم بتوصيل أنبوب جهاز قياس الضغط بالحلمة (الشكل 1. F). 3. Remove the cover of the pressure switch. 3. قم بإزالة غطاء مفتاح الضغط. 4. Slowly release pressure of the main gas supply line until the desired value is reached. 4. حرر ببطء ضغط خط إمداد الغاز الرئيسي حتى يتم الوصول إلى القيمة المطلوبة. 5. Turn dial slowly until contact 1-3 opens and contact 2-3 closes. 5. قم بتدوير الاتصال الهاتفي ببطء حتى يفتح الاتصال 1-3 ويتم إغلاق الاتصال 2-3. 6. Replace the cover. 6. استبدال الغطاء. 7. Disconnect the pressure measurement device and replace the screw. 7. افصل جهاز قياس الضغط واستبدل المسمار. Checkout Checking cut-off pressure After the installation is completed, continue with the following procedures: 1. Slowly close manual main valve with the burner in operation. الخروج فحص ضغط القطع بعد اكتمال التثبيت ، تابع الإجراءات التالية: 1. أغلق الصمام الرئيسي اليدوي ببطء مع تشغيل الموقد. Shut down should occur when the pressure drops below the set point and the alarm (if connected) should be energized. يجب أن يحدث الإغلاق عندما ينخفض الضغط إلى ما دون النقطة المحددة ويجب تنشيط الإنذار (إذا كان متصلاً). 2. Re open the manual main valve. 2. أعد فتح الصمام الرئيسي اليدوي. The pressure should rise and exceed the set point value, the burner should start up and the alarm turn off after the reset button is depressed. يجب أن يرتفع الضغط ويتجاوز قيمة النقطة المحددة ، ويجب أن يبدأ تشغيل الموقد ويتم إيقاف التنبيه بعد الضغط على زر إعادة الضبط.
اتصل شخص: Sales Manager
الهاتف :: +8613510133539